Ratchet Tie Down
Ratchet tie down straps for cargo restraint: 25 mm to 100 mm webbing, with J hook, double J hook, flat hook, swan hook, snap hook, E-track fitting or chain anchor end, built to EN 12195-2 and marked with the lashing capacity.
Three numbers on the label, and they are not interchangeable
An EN 12195-2 lashing strap carries a lashing capacity (LC), a standard tension force (STF) and a minimum breaking strength. LC is what the strap may restrain in service. STF is the tension the ratchet can pull in by hand. Breaking strength is the point of failure, and the standard requires at least twice LC.
A supplier quoting 5 t without saying which of the three numbers that is has not quoted anything yet. Ask for the LC.
| Term | What it means | How to use it |
|---|---|---|
| LC — lashing capacity | The load the strap may restrain in service | The only number worth comparing between suppliers |
| STF — standard tension force | Tension the ratchet applies by hand | Tells you how hard the load is actually clamped |
| Breaking strength | Where the strap fails | Must be at least 2 × LC under EN 12195-2 |
Hook ends: match the anchor, not the catalog photo
The hook is chosen by what it has to attach to. The same strap body is built with any of the ends below, and mixing them up is the most common reason a container arrives with a loose strap.
| End fitting | Fits | Typical load |
|---|---|---|
| Double J hook | D-rings, side rails, stake pockets | General flatbed and trailer cargo |
| Flat hook | Rub rails and flatbed edges | Steel, timber and machinery on flatbeds |
| Swan / rave hook | Curtain-side rave rails | Curtain-side trailer loads |
| Snap hook | Rings and eyelets | Light cargo, ATV, motorcycle, boat |
| Chain anchor and hook | Chain, binders, heavy anchor points | Heavy machinery and steel |
| E-track fitting | E-track and logistics rails | Van and trailer interior loads |
Width and capacity at a glance
Typical ranges for our standard range. Exact LC depends on webbing grade and end fitting, and the label on the sample you receive is the number that counts.
| Webbing width | Typical lashing capacity | Where it is used |
|---|---|---|
| 25 mm · 1 in | 500 to 800 kg | Motorcycle, ATV, light cargo, boat |
| 35 mm · 1.4 in | 1 to 2 t | Small trailers, plant, general cargo |
| 50 mm · 2 in | 2 to 5 t | Flatbeds, container lashing, machinery |
| 75 mm · 3 in | 4 to 5 t | Heavy trailers, steel, timber |
| 100 mm · 4 in | winch straps to 16,200 lb breaking | Low-bed and step-deck trailers |
A ratchet strap is not a lifting sling
EN 12195-2 covers load restraint only. A lashing strap must never be used to lift a load, and a lifting sling must never be used to lash one: the standards, the safety factors and the test regimes are different.
If a job needs both, it needs two products. We make both, and we will tell you which is which rather than sell you the wrong one.
Questions buyers ask before ordering
What does LC mean on a ratchet strap?+
Lashing capacity — the load the strap may restrain in service, marked on the label. It is not the breaking strength. Under EN 12195-2 the breaking strength must be at least twice the LC, so a strap marked LC 2500 daN breaks above 5000 daN.
Can I use a ratchet tie down to lift?+
No. Lashing straps are for load restraint only and must never be used as lifting equipment. Lifting slings are built to EN 1492 with a 7:1 factor and different testing; lashing straps are built to EN 12195-2.
What length do you make, and how is it measured?+
Made to the length you specify, measured end to end including the hooks. Tell us the span between anchor points and the load height and we will work out the length, allowing for the ratchet take-up.
Which end do I need for E-track?+
The E-track fitting, which clips into the rail and releases with the spring-loaded button. It is available on 25 mm and 50 mm straps and replaces the hook end.
Can you print our logo on the webbing?+
Yes — printed webbing or a woven label, plus your part number. Send artwork as PDF or AI with the Pantone reference; there is a minimum order quantity for custom printing.
Do you supply EN 12195-2 test reports?+
Each batch is pull tested and ships with a certificate of conformity stating LC and breaking strength. Third-party testing through TÜV or SGS is available on request and adds lead time.
Need ratchet tie down to your own specification?
Widths, lengths, colors, logo printing, hook types and packaging — all made to order. Send your drawing or reference sample.